Opel Omega

since 1993-1999 release

Repair and operation of the car


Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines of 2,0 liters
   + 3.2. DOHC engines of 2,0 liters
   + 3.3. 2,5 and 3,0 liters engines
   + 3.4. Partition of all petrol engines
   - 3.5. 2,0 liters diesel engine
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine installed in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gas distribution mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a bent shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil heater
      3.5.16. Sealing rings of a bent shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      - 3.5.19. Capital repairs of the 2,0 liters diesel engine
         3.5.19.1. Technical characteristics
         3.5.19.2. Head of the block of cylinders
         3.5.19.3. Pistons and rods
         3.5.19.4. Bent shaft
         3.5.19.5. Block of cylinders of the engine
         3.5.19.6. Radical bearings and bearings of rods
         3.5.19.7. Engine balance of assembly at capital repairs
         3.5.19.8. Piston rings
         3.5.19.9. Working gaps of radical bearings
         3.5.19.10. Working gaps of conrod bearings
         3.5.19.11. Start of the engine after capital repairs
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment



3.5.19.5. Block of cylinders of the engine

 Cleaning

PERFORMANCE ORDER
1. Remove all details and electric sensors from the block of cylinders. For full cleaning remove technological caps. For removal of caps drill in them small openings and in openings screw in the self-cutting screw. Having pulled for a screw head, remove a cap.
2. Shoot oil sprays with an internal part of pistons. They are fixed by bolts.
3. Remove all traces of laying from the interfaced surfaces of the block of cylinders of the engine.
4. Remove all caps of the oil highway. At installation use new caps.
5. The most polluted places clear the ferry.
6. Clear all lubricant openings and the oil highway. Wash out all internal channels a stream of warm water until water does not come out pure. It is necessary to drain completely the block of cylinders and to grease with a thin butter layer all interfaced surfaces for prevention of emergence of corrosion. Also grease engine cylinders. If there is a compressed air, use it to accelerate process of drying and to blow all lubricant openings and highways.
7. Carefully clear all carving openings, using a tap with the corresponding carving then blow openings compressed air.
8. Install traffic jams to the oil highway in the block of cylinders of the engine and reliably fix them.
9. Establish oil sprays.
10. If the engine is not subject to immediate assembly, close the block of cylinders a big plastic bag to protect it from pollution.
11. Visually check the block of cylinders for corrosion existence. Check integrity of a carving in carving openings.
12. Check diameter of cylinders of the engine for wear on existence of a step in the top part of the cylinder.
13. In the presence of the measuring tool measure diameter of a sleeve of each cylinder in the top part (under a wear step) in the center and at the basis parallel to an axis of a bent shaft. Then perform the same measurements perpendicular to an axis cranked a shaft and compare them to specifications. Repeat the procedure of measurement on other sleeves of cylinders. If wear exceeds admissible values, it is necessary to chisel cylinders and to install new pistons of the increased size. The increased size of pistons (0,5 mm) is available to all engines.