Opel Omega

since 1993-1999 release

Repair and operation of the car


Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines of 2,0 liters
   + 3.2. DOHC engines of 2,0 liters
   + 3.3. 2,5 and 3,0 liters engines
   + 3.4. Partition of all petrol engines
   - 3.5. 2,0 liters diesel engine
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine installed in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gas distribution mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a bent shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil heater
      3.5.16. Sealing rings of a bent shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      + 3.5.19. Capital repairs of the 2,0 liters diesel engine
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment



3.5.18. Suspension brackets of the power unit
GENERAL INFORMATION

For improvement of access to a suspension bracket of the power unit lift a forward part of the car and record on supports.

Check

PERFORMANCE ORDER
1. Check a condition of rubber elements of support of the engine for existence of cracks, aging and stratification.
2. Check reliability of fastening of engine mounts.
3. Moving the engine here and there, check a side play in engine mounts. New elements of a suspension bracket have to have an insignificant side play even.
Right suspension bracket
4. Remove a casing of the air filter and the right inlet air channel.
5. Establish a jack under the engine and through wooden whetstone raise the engine until all weight of the engine is not perceived by a jack.
6. Unscrew nuts of fastening of a support to a basic arm.
7. Raise the engine and unscrew the lower nut of fastening of a support and remove an engine mount.
8. Check suspension bracket elements for existence of wear or damage and, if necessary, replace.
9. Fix a suspension bracket of the power unit to a body and tighten fastening nuts the required moment.
10. Establish a basic arm to the engine and tighten fastening bolts the required moment. Establish the right suspension bracket on the top part of a support and tighten a fastening nut the required moment.
Left suspension bracket
11. Unscrew a nut of fastening of the right suspension bracket of the power unit.
12. Lift a forward part of the car and record on supports.
13. Establish a jack under the engine and through wooden whetstone raise the engine until all weight of the engine is not perceived by a jack. Unscrew a nut (it is specified by an arrow), the fixing left suspension bracket to a forward lower frame.
14. Raise the engine, unscrew bolts of fastening of the left suspension bracket to the transmission and take a suspension bracket.
15. Check all elements of a suspension bracket for signs of wear and, if necessary, replace.
16. Establish the left suspension bracket and slightly tighten a fastening nut.
17. Screw up bolts of fastening of the left suspension bracket to the transmission.
18. Lower the engine and put the clamp of fastening of the left suspension bracket to the lower frame.
19. Lower the car and tighten nuts of fastening of the left suspension bracket the required moment.
Back suspension bracket
20. Remove the right power shaft.
21. Remove a forward exhaust pipe.
22. Weaken bolts of fastening of a rod of gear shifting and disconnect a gear shifting rod from draft of control of the transmission.
23. Unscrew a nut of fastening of the right suspension bracket.
24. Establish a jack under the engine and through wooden whetstone raise engine weight until all weight of the engine is not perceived by a jack.
25. Unscrew bolts of fastening of a back suspension bracket to the lower frame. If it is necessary, unscrew bolts and take a back suspension bracket from under the car.
26. Establish a back suspension bracket and fix it to the power unit.
27. Fix a back suspension bracket to the lower frame, having tightened fastening bolts the required moment.
28. Put the clamp of fastening of the right suspension bracket, having tightened it the required moment.
29. Connect a rod of gear shifting and adjust the gear shifting mechanism.
30. Establish the right power shaft.

31. Establish a forward exhaust pipe.