Opel Omega

since 1993-1999 release

Repair and operation of the car



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines of 2,0 liters
   - 3.2. DOHC engines of 2,0 liters
      3.2.1. Technical characteristics
      3.2.2. Check of a compression
      3.2.3. Top Dead Point (TDP) of the N1 piston
      3.2.4. Cover of camshafts
      3.2.5. Pulley of a bent shaft
      3.2.6. Covers of a gas-distributing belt
      3.2.7. Gas-distributing belt
      3.2.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and pushers
      3.2.11. Head of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. System of an equilibration of a bent shaft (engines since 1998)
      3.2.15. Flywheel
      3.2.16. Epiploons of a bent shaft
      3.2.17. Fastenings of the engine and transmission
   + 3.3. 2,5 and 3,0 liters engines
   + 3.4. Partition of all petrol engines
   + 3.5. 2,0 liters diesel engine
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


Три значение числа

3.2.7. Gas-distributing belt

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator and install the N1 piston in VMT.
2. Remove a pulley of a bent shaft.
3. Weaken a bolt (1) of a natyazhitel of a gas-distributing belt, turn the lever (2) natyazhitel clockwise against the stop and tighten a bolt.
4. Take off a gas-distributing belt and note its direction of rotation.
5. Carefully examine a belt on existence of wear and damages, if necessary replace it.

Installation

Combination of synchronizing tags

1. Tags of asterisks of camshafts

2. Tags on covers of bearings

3. Combination of a tag of an asterisk of a bent shaft with a cut in a casing of the oil pump

Arrangement of the index of a natyazhitel concerning a cut in a back plate

 
1. Index of a natyazhitel
2. A cut in a back plate
A. A new belt, a natyazhitel without tags
B. A new belt, a natyazhitel with tags
C. An old belt, a natyazhitel without tags
D. An old belt, a natyazhitel with tags

PERFORMANCE ORDER
1. Carefully clean asterisks of cranked and distributive shaft. Check combination of tags of asterisks of camshafts with tags on covers of bearings, combination of a tag of an asterisk of a bent shaft with a cut in a casing of the oil pump (see rice. Combination of synchronizing tags).
2. Put on a belt asterisks.
3. Weaken a bolt of a natyazhitel and turn the lever of a natyazhitel counterclockwise against the stop. Tighten a bolt of a natyazhitel.
4. Check whether synchronizing tags are combined.
5. Turn a bent shaft on two whole revolutions.
6. Check tags and again weaken a bolt of a natyazhitel.
7. If you established a new gas-distributing belt, adjust a natyazhitel so that his index was directed to a cut or to a tag of "NEW" (see rice. An arrangement of the index of a natyazhitel concerning a cut in a back plate) also tighten a bolt.
8. If you established an old belt, the index of a natyazhitel has to be directed to 4 mm more to the left of a cut or has to indicate a tag of "USED" (see rice. An arrangement of the index of a natyazhitel concerning a cut in a back plate).
9. Establish the remained details.